The path given for the missing file is from a project previously loaded on the board. The file does exist on the computer's hard drive.
What did I do wrong to cause this?
How do I correct this issue?
Code: Select all
ets Jul 29 2019 12:21:46
rst:0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 188777542, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:2
load:0x3fff0030,len:4
load:0x3fff0034,len:6956
load:0x40078000,len:13072
xtensa-esp32-elf-addr2line -pfiaC -e c:\users\dg\source\repos\esp32\blink\blink\build\udp_server.elf 0x40078000: [WinError 2] The system cannot find the file specified
load:0x40080400,len:3896
xtensa-esp32-elf-addr2line -pfiaC -e c:\users\dg\source\repos\esp32\blink\blink\build\udp_server.elf 0x40080400: [WinError 2] The system cannot find the file specified
entry 0x40080688
xtensa-esp32-elf-addr2line -pfiaC -e c:\users\dg\source\repos\esp32\blink\blink\build\udp_server.elf 0x40080688: [WinError 2] The system cannot find the file specified
I (30) boot: ESP-IDF v4.1-dirty 2nd stage bootloader
I (30) boot: compile time 21:12:40
I (30) boot: chip revision: 3
I (33) boot_comm: chip revision: 3, min. bootloader chip revision: 0
I (40) boot.esp32: SPI Speed : 40MHz
I (45) boot.esp32: SPI Mode : DIO
I (49) boot.esp32: SPI Flash Size : 4MB
I (54) boot: Enabling RNG early entropy source...
I (59) boot: Partition Table:
I (63) boot: ## Label Usage Type ST Offset Length
I (70) boot: 0 nvs WiFi data 01 02 00009000 00006000
I (78) boot: 1 phy_init RF data 01 01 0000f000 00001000
I (85) boot: 2 factory factory app 00 00 00010000 00100000
I (93) boot: End of partition table
I (97) boot_comm: chip revision: 3, min. application chip revision: 0
I (104) esp_image: segment 0: paddr=0x00010020 vaddr=0x3f400020 size=0x04c58 ( 19544) map
I (120) esp_image: segment 1: paddr=0x00014c80 vaddr=0x3ffb0000 size=0x0194c ( 6476) load
I (124) esp_image: segment 2: paddr=0x000165d4 vaddr=0x40080000 size=0x00404 ( 1028) load
xtensa-esp32-elf-addr2line -pfiaC -e c:\users\dg\source\repos\esp32\blink\blink\build\udp_server.elf 0x40080000: [WinError 2] The system cannot find the file specified
I (131) esp_image: segment 3: paddr=0x000169e0 vaddr=0x40080404 size=0x08b80 ( 35712) load
xtensa-esp32-elf-addr2line -pfiaC -e c:\users\dg\source\repos\esp32\blink\blink\build\udp_server.elf 0x40080404: [WinError 2] The system cannot find the file specified
I (155) esp_image: segment 4: paddr=0x0001f568 vaddr=0x00000000 size=0x00ab0 ( 2736)
I (156) esp_image: segment 5: paddr=0x00020020 vaddr=0x400d0020 size=0x12a14 ( 76308) map
xtensa-esp32-elf-addr2line -pfiaC -e c:\users\dg\source\repos\esp32\blink\blink\build\udp_server.elf 0x400d0020: [WinError 2] The system cannot find the file specified
I (195) boot: Loaded app from partition at offset 0x10000
I (196) boot: Disabling RNG early entropy source...
I (196) cpu_start: Pro cpu up.
I (200) cpu_start: Application information:
I (204) cpu_start: Project name: hello-world
I (210) cpu_start: App version: 1
I (214) cpu_start: Compile time: Jan 15 2021 21:09:42
I (220) cpu_start: ELF file SHA256: bfc1edfe4da46a32...
I (226) cpu_start: ESP-IDF: v4.1-dirty
I (231) cpu_start: Single core mode
I (236) heap_init: Initializing. RAM available for dynamic allocation:
I (243) heap_init: At 3FFAE6E0 len 00001920 (6 KiB): DRAM
I (249) heap_init: At 3FFB2068 len 0002DF98 (183 KiB): DRAM
I (255) heap_init: At 3FFE0440 len 0001FBC0 (126 KiB): D/IRAM
I (262) heap_init: At 40078000 len 00008000 (32 KiB): IRAM
I (268) heap_init: At 40088F84 len 0001707C (92 KiB): IRAM
I (274) cpu_start: Pro cpu start user code
I (291) spi_flash: detected chip: generic
I (292) spi_flash: flash io: dio
I (292) cpu_start: Starting scheduler on PRO CPU.
Hello world!
This is ESP32 chip with 1 CPU cores, WiFi/BT/BLE, silicon revision 3, 4MB embedded flash
Restarting in 10 seconds...