what will cause reboot issue

[alvin_xie]

I power off the ESP32 for 5 sec. and then power on it.
But the ESP32 will always reboot.

here is the log:

Code: Select all

...
rst:0x10 (RTCWDT_RTC_RESET),boot:0x33 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:2
cmd len -1
ets_main.c 371 
ets Jun  8 2016 00:22:57

rst:0x10 (RTCWDT_RTC_RESET),boot:0x33 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:2
cmd len -1
ets_main.c 371 
ets Jun  8 2016 00:22:57

rst:0x10 (RTCWDT_RTC_RESET),boot:0x33 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:2
cmd len -1
ets_main.c 371 
ets Jun  8 2016 00:22:57

rst:0x10 (RTCWDT_RTC_RESET),boot:0x33 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:2
load:0x3fff0018,len:4
load:0x3fff001c,len:5772
load:0x40078000,len:0
load:0x40078000,len:13804
csum err:0xe6!=0xc8
ets_main.c 371 
ets Jun  8 2016 00:22:57

rst:0x10 (RTCWDT_RTC_RESET),boot:0x33 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:2
cmd len -1
ets_main.c 371 
ets Jun  8 2016 00:22:57
...

what will cause this issue?

[chegewara]

Maybe this?

Code: Select all

csum err:0xe6!=0xc8

[WiFive]

0x33 means you have gpio12 pulled up and should have 1.8v flash (wrover or d2wd), do you?

[Pibbotley]

As above, disconnect pin 12 and try again. I avoid pin 12 if I can.

[ESP_igrr]

Alternatively, use espefuse.py to set flash voltage to 3.3V. Then the state of GPIO12 will not matter.

[Pibbotley]

I've learned something, thanks

[alvin_xie]

Alternatively, use espefuse.py to set flash voltage to 3.3V. Then the state of GPIO12 will not matter.

Code: Select all

use espefuse.py to set flash voltage to 3.3V.

how to do this?

[ESP_igrr]

Please see https://github.com/espressif/esptool/wi ... e-vdd_sdio