HUB: Bad transfer status 1: CHECK_SHORT_DEV_DESC E ;HUB: Stage failed: CHECK_SHORT_DEV_DESC error in esp32S3

[mano-30]

I was trying out the uvc example project by connecting the webcam to a custom PCB with the ESP32S3 chip. I used a USB breakout board to connect the webcam to the ESP32S3. I connected D- to GPIO19 and D+ to GPIO20. I connected VBUS to 5V on the breakout board and GND pin to ESP's GND. When I connected the webcam to the ESP, I am getting bad transfer status 1. However, if I connect the webcam to the microusb port of ESP32S3 DevKit C, I am not facing this issue. I am attaching the logs of the code where I am facing this issue.

Code: [Select all] [Expand/Collapse]

1. I (31) boot: ESP-IDF v5.3-dirty 2nd stage bootloader
2. I (31) boot: compile time Aug 27 2024 15:00:45
3. I (31) boot: Multicore bootloader
4. I (35) boot: chip revision: v0.1
5. I (38) boot.esp32s3: Boot SPI Speed : 80MHz
6. I (43) boot.esp32s3: SPI Mode       : DIO
7. I (48) boot.esp32s3: SPI Flash Size : 2MB
8. I (53) boot: Enabling RNG early entropy source...
9. I (58) boot: Partition Table:
10. I (62) boot: ## Label            Usage          Type ST Offset   Length
11. I (69) boot:  0 nvs              WiFi data        01 02 00009000 00006000
12. I (76) boot:  1 phy_init         RF data          01 01 0000f000 00001000
13. I (84) boot:  2 factory          factory app      00 00 00010000 00100000
14. I (91) boot: End of partition table
15. I (96) esp_image: segment 0: paddr=00010020 vaddr=3c0a0020 size=257d4h (153556) map
16. I (132) esp_image: segment 1: paddr=000357fc vaddr=3fc9ae00 size=04f98h ( 20376) load
17. I (136) esp_image: segment 2: paddr=0003a79c vaddr=40374000 size=0587ch ( 22652) load
18. I (142) esp_image: segment 3: paddr=00040020 vaddr=42000020 size=9a59ch (632220) map
19. I (260) esp_image: segment 4: paddr=000da5c4 vaddr=4037987c size=11488h ( 70792) load
20. I (285) boot: Loaded app from partition at offset 0x10000
21. I (285) boot: Disabling RNG early entropy source...
22. I (297) esp_psram: Found 2MB PSRAM device
23. I (297) esp_psram: Speed: 40MHz
24. I (297) cpu_start: Multicore app
25. I (717) esp_psram: SPI SRAM memory test OK
26. I (726) cpu_start: Pro cpu start user code
27. I (726) cpu_start: cpu freq: 240000000 Hz
28. I (726) app_init: Application information:
29. I (729) app_init: Project name:     usb-uvc
30. I (734) app_init: App version:      1
31. I (739) app_init: Compile time:     Aug 28 2024 18:57:16
32. I (745) app_init: ELF file SHA256:  5a8b9cb46...
33. I (750) app_init: ESP-IDF:          v5.3-dirty
34. I (755) efuse_init: Min chip rev:     v0.0
35. I (760) efuse_init: Max chip rev:     v0.99
36. I (765) efuse_init: Chip rev:         v0.1
37. I (770) heap_init: Initializing. RAM available for dynamic allocation:
38. I (777) heap_init: At 3FCA4188 len 00045588 (277 KiB): RAM
39. I (783) heap_init: At 3FCE9710 len 00005724 (21 KiB): RAM
40. I (789) heap_init: At 3FCF0000 len 00008000 (32 KiB): DRAM
41. I (795) heap_init: At 600FE100 len 00001EE8 (7 KiB): RTCRAM
42. I (802) esp_psram: Adding pool of 2048K of PSRAM memory to heap allocator
43. I (810) spi_flash: detected chip: generic
44. I (813) spi_flash: flash io: dio
45. W (817) spi_flash: Detected size(4096k) larger than the size in the binary image header(2048k). Using the size in the binary image header.
46. I (831) sleep: Configure to isolate all GPIO pins in sleep state
47. I (837) sleep: Enable automatic switching of GPIO sleep configuration
48. I (845) main_task: Started on CPU0
49. I (855) esp_psram: Reserving pool of 32K of internal memory for DMA/internal allocations
50. I (855) main_task: Calling app_main()
51. I (865) gpio: GPIO[0]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 1| Pulldown: 0| Intr:0
52. W (875) USB HOST: User callback to set USB device configuration is enabled, but not used
53. I (915) example_connect: Start example_connect.
54. I (915) pp: pp rom version: e7ae62f
55. I (915) net80211: net80211 rom version: e7ae62f
56. I (935) wifi:wifi driver task: 3fcbaec4, prio:23, stack:6656, core=0
57. I (935) wifi:wifi firmware version: 0caa81945
58. I (935) wifi:wifi certification version: v7.0
59. I (935) wifi:config NVS flash: enabled
60. I (935) wifi:config nano formating: disabled
61. I (945) wifi:Init data frame dynamic rx buffer num: 8
62. I (945) wifi:Init static rx mgmt buffer num: 5
63. I (955) wifi:Init management short buffer num: 32
64. I (955) wifi:Init static tx buffer num: 8
65. I (955) wifi:Init tx cache buffer num: 32
66. I (965) wifi:Init static tx FG buffer num: 2
67. I (965) wifi:Init static rx buffer size: 1600
68. I (975) wifi:Init static rx buffer num: 8
69. I (975) wifi:Init dynamic rx buffer num: 8
70. I (975) wifi_init: rx ba win: 8
71. I (985) wifi_init: accept mbox: 6
72. I (985) wifi_init: tcpip mbox: 32
73. I (995) wifi_init: udp mbox: 6
74. I (995) wifi_init: tcp mbox: 6
75. I (995) wifi_init: tcp tx win: 15000
76. I (1005) wifi_init: tcp rx win: 5760
77. I (1005) wifi_init: tcp mss: 1440
78. I (1015) wifi_init: WiFi IRAM OP enabled
79. I (1015) wifi_init: WiFi RX IRAM OP enabled
80. I (1025) phy_init: phy_version 680,a6008b2,Jun  4 2024,16:41:10
81. I (1055) wifi:mode : sta (f0:f5:bd:6e:6f:d8)
82. I (1055) wifi:enable tsf
83. I (1065) example_connect: Connecting to <wifi_name>...
84. I (1065) example_connect: Waiting for IP(s)
85. E (2415) HUB: Bad transfer status 1: CHECK_SHORT_DEV_DESC
86. E (2415) HUB: Stage failed: CHECK_SHORT_DEV_DESC
87. I (3815) wifi:new:<6,0>, old:<1,0>, ap:<255,255>, sta:<6,0>, prof:1, snd_ch_cfg:0x0
88. I (3815) wifi:state: init -> auth (0xb0)
89. I (3825) wifi:state: auth -> assoc (0x0)
90. I (3825) wifi:state: assoc -> run (0x10)
91. I (3845) wifi:connected with <wifi_name>, aid = 6, channel 6, BW20, bssid = e4:55:a8:28:f4:1e
92. I (3845) wifi:security: WPA2-PSK, phy: bgn, rssi: -59
93. I (3845) wifi:pm start, type: 1
94. I (3845) wifi:dp: 1, bi: 102400, li: 3, scale listen interval from 307200 us to 307200 us
95. I (3855) wifi:set rx beacon pti, rx_bcn_pti: 0, bcn_timeout: 25000, mt_pti: 0, mt_time: 10000
96. I (3875) wifi:<ba-add>idx:0 (ifx:0, e4:55:a8:28:f4:1e), tid:0, ssn:0, winSize:64
97. I (3915) wifi:AP's beacon interval = 102400 us, DTIM period = 1
98. I (4865) esp_netif_handlers: example_netif_sta ip: 192.168.11.132, mask: 255.255.252.0, gw: 192.168.8.1
99. I (4865) example_connect: Got IPv4 event: Interface "example_netif_sta" address: 192.168.11.132
100. I (4915) example_connect: Got IPv6 event: Interface "example_netif_sta" address: fe80:0000:0000:0000:f2f5:bdff:fe6e:6fd8, type: ESP_IP6_ADDR_IS_LINK_LOCAL

GeSHi © Codebox Plus Extension

I have set all the USB-OTG menuconfig parameters to 500 ms as well. Is this a hardware issue or do I have to make some changes in the code?

[chegewara]

Can you post sdkconfig? That may help to spot problem.
In general uvc descriptors are very long, even up to 1500 bytes, so please to compare with uvc example code.

[mano-30]

Here is the sdkconfig file. I will look into the uvc parameters, but if it works for the devkit, then it should work for the custom pcb as well?

[chegewara]

Yeah, if its the same code then its suggesting hardware problem.

I wanted to check this param, just to make sure

CONFIG_USB_HOST_CONTROL_TRANSFER_MAX_SIZE

Sometimes it may be issue with some USB devices, when descriptor is 255 or 256 bytes long, i dont remember. But again, if you are testing with the same firmware and the same camera, then its not the case.