I'm able to upload and run the code fine with the Arduino IDE but I can't connect to the device through ethernet. I have it connected to my laptop using a Cat5e cable but I'm not sure what to set the IP address to.
I set the IP to 192.168.0.112 and the gateway to 192.168.0.1 in the code, then on my laptop(running windows 10) I set the ethernet ipv4 properties to match this:
IP Address: 192.168.0.112
Subnet mask: 255.255.255.0
Default gateway: 192.168.0.1
DNS: 8.8.8.8
I power up the device and in the serial output it says:
IPv4: 192.168.0.112
and looks like it is starting all ok.
But I can't access the webserver, if I try pinging 192.168.0.112 I get a "request timed out" message and if I try to open that IP address in the browser it times out as well
So my question is what am I doing wrong? What do I set the addresses to so I can get it working?
thanks! B
Code: Select all
#define DEBUG_ETHERNET_WEBSERVER_PORT Serial
// Debug Level from 0 to 4
#define _ETHERNET_WEBSERVER_LOGLEVEL_ 3
#include <WebServer_WT32_ETH01.h>
WiFiServer server(80);
169.254.11.126
// Select the IP address according to your local network
IPAddress myIP(192, 168, 0, 112);
IPAddress myGW(192, 168, 0, 1);
IPAddress mySN(255, 255, 255, 0);
// Google DNS Server IP
IPAddress myDNS(8, 8, 8, 8);
int reqCount = 0; // number of requests received
void setup()
{
Serial.begin(115200);
Serial.println("setup begin");
while (!Serial);
// Using this if Serial debugging is not necessary or not using Serial port
//while (!Serial && (millis() < 3000));
Serial.print("\nStarting WebServer on " + String(ARDUINO_BOARD));
Serial.println(" with " + String(SHIELD_TYPE));
Serial.println(WEBSERVER_WT32_ETH01_VERSION);
// To be called before ETH.begin()
WT32_ETH01_onEvent();
//bool begin(uint8_t phy_addr=ETH_PHY_ADDR, int power=ETH_PHY_POWER, int mdc=ETH_PHY_MDC, int mdio=ETH_PHY_MDIO,
// eth_phy_type_t type=ETH_PHY_TYPE, eth_clock_mode_t clk_mode=ETH_CLK_MODE);
//ETH.begin(ETH_PHY_ADDR, ETH_PHY_POWER, ETH_PHY_MDC, ETH_PHY_MDIO, ETH_PHY_TYPE, ETH_CLK_MODE);
ETH.begin(ETH_PHY_ADDR, ETH_PHY_POWER);
// Static IP, leave without this line to get IP via DHCP
//bool config(IPAddress local_ip, IPAddress gateway, IPAddress subnet, IPAddress dns1 = 0, IPAddress dns2 = 0);
ETH.config(myIP, myGW, mySN, myDNS);
WT32_ETH01_waitForConnect();
// start the web server on port 80
server.begin();
}
void loop()
{
// listen for incoming clients
WiFiClient client = server.available();
if (client)
{
Serial.println(F("New client"));
// an http request ends with a blank line
bool currentLineIsBlank = true;
while (client.connected())
{
if (client.available())
{
char c = client.read();
Serial.write(c);
// if you've gotten to the end of the line (received a newline
// character) and the line is blank, the http request has ended,
// so you can send a reply
if (c == '\n' && currentLineIsBlank)
{
Serial.println(F("Sending response"));
// send a standard http response header
// use \r\n instead of many println statements to speedup data send
client.print(
"HTTP/1.1 200 OK\r\n"
"Content-Type: text/html\r\n"
"Connection: close\r\n" // the connection will be closed after completion of the response
"Refresh: 20\r\n" // refresh the page automatically every 20 sec
"\r\n");
client.print("<!DOCTYPE HTML>\r\n");
client.print("<html>\r\n");
client.print(String("<h2>Hello World from ") + BOARD_NAME + "!</h2>\r\n");
client.print("Requests received: ");
client.print(++reqCount);
client.print("<br>\r\n");
client.print("<br>\r\n");
client.print("</html>\r\n");
break;
}
if (c == '\n')
{
// you're starting a new line
currentLineIsBlank = true;
}
else if (c != '\r')
{
// you've gotten a character on the current line
currentLineIsBlank = false;
}
}
}
// give the web browser time to receive the data
delay(10);
// close the connection:
client.stop();
Serial.println(F("Client disconnected"));
}
}