[已解决] 求助，启动的时候ram问题，请问怎么解决

[rui1352]

Rebooting...
[0;32mI (12) boot: ESP-IDF v3.3-beta1-482-gf746b0d76-dirty 2nd stage bootloader[0m
[0;32mI (12) boot: compile time 11:07:06[0m
[0;32mI (19) boot: Enabling RNG early entropy source...[0m
[0;32mI (19) boot: SPI Speed : 40MHz[0m
[0;32mI (22) boot: SPI Mode : DIO[0m
[0;32mI (26) boot: SPI Flash Size : 8MB[0m
[0;32mI (30) boot: Partition Table:[0m
[0;32mI (33) boot: ## Label Usage Type ST Offset Length[0m
[0;32mI (41) boot: 0 nvs WiFi data 01 02 00009000 00004000[0m
[0;32mI (48) boot: 1 otadata OTA data 01 00 0000d000 00002000[0m
[0;32mI (56) boot: 2 phy_init RF data 01 01 0000f000 00001000[0m
[0;32mI (63) boot: 3 factory factory app 00 00 00010000 00120000[0m
[0;32mI (71) boot: 4 ota_0 OTA app 00 10 00130000 00130000[0m
[0;32mI (78) boot: 5 ota_1 OTA app 00 11 00260000 00130000[0m
[0;32mI (85) boot: 6 storage Unknown data 01 82 00390000 00470000[0m
[0;32mI (93) boot: End of partition table[0m
[0;31mE
[12:01:40.064]收←◆(97) boot: ota data partition invalid, falling back to factory[0m
[0;32mI (104) esp_image: segment 0: paddr=0x00010020 vaddr=0x3f400020 size=0x32b68 (207720) map[0m

[12:01:40.120]收←◆[0;32mI (186) esp_image: segmen
[12:01:40.140]收←◆t 1: paddr=0x00042b90 vaddr=0x3ffb0000 size=0x03114 ( 12564) load[0m
[0;32mI (191) esp_image: segment 2: paddr=0x00045cac vaddr=0x40080000 size=0x00400 ( 1024) load[0m
[0;32mI (193) esp_image: segment 3: paddr=0x000460b4 vaddr=0x40080400 size=0x09f5c ( 40796) load[0m
[0;32mI (218) esp_image: segment 4: paddr=0x00050018 vaddr=0x400d0018 size=0xbccf8 (773368) map[0m

[12:01:40.424]收←◆[0;32mI (489) esp_image: segment 5: paddr=0x0010cd18 vaddr=0x4008a35c size=0x0f5cc ( 62924) load[0m
[0;32mI (516) esp_image: segment 6: paddr=0x0011c2ec vaddr=0x400c0000 size=0x0006c ( 108) load[0m
[0;32mI (531) boot: Loaded app from partition at offset 0x10000[0m
[0;32mI (531) boot: Disabling RNG early entropy source...[0m
[0;31mE (533) spiram: Expected 4096KiB chip but found 8192KiB chip. Bailing out..[0m
[0;31mE (539) cpu_start: Failed to init external RAM![0m
abort() was called at PC 0x400816f1 on core 0

ELF file SHA256: a8026e008d58dd1abfb4643ae9ed1e4e39d9e6a1ed6183db9b2f11173b6d53f5

Backtrace: 0x4008d0bc:0x3ffe3bb0 0x4008d305:0x3ffe3bd0 0x400816f1:0x3ffe3bf0 0x40079367:0x3ffe3c30 0x40079419:0x3ffe3c60 0x40079437:0x3ffe3ca0 0x4007971d:0x3ffe3cc0 0x40080792:0x3ffe3df0 0x40007c31:0x3ffe3eb0 0x4000073d:0x3ffe3f20



我使用的是ESP32-WROVER

[ESP_Dazz]

Code: Select all

[0;31mE (533) spiram: Expected 4096KiB chip but found 8192KiB chip. Bailing out..[0m
[0;31mE (539) cpu_start: Failed to init external RAM![0m

你使用的ESP WROVER包含8MB SPI-RAM，但是配置里选了4MB SPI-RAM。请用make menuconfig更改配置。有关选项在Component config -> ESP32-specific -> SPI RAM config -> Type of SPI RAM chip in use，然后选ESP-PSRAM64 或 Auto-detect

[rui1352]

问题按楼上的处理，已解决，谢谢！