rm3100 status register not changing
Posted: Sun Dec 25, 2022 12:28 pm
The rm3100 is working with Arduino Leonardo. I am trying to make it work with esp32.
I am able to write to the registers of an rm3100 and read them. I tried to write to the register and then read its value - it works as expected.
But the measurement registers not changing and the senior bit of the status register (0x34) is always 0. DRDY line stays low.
I tried continuous mode (wrote 0x71 to the register 0x01) and single measurement (wrote 0x70 to the register 0x00).
The following points look suspicious:
1) According to the datasheet https://www.pnicorp.com/wp-content/uplo ... -R09-1.pdf – I need to add 0x80 to the register address when reading.
But it doesn’t work in my case – when I add 0x80 – I am getting 0. But when I read without adding – I am getting correct results.
2. According to the datasheet – I need to send “stop” when after sending the register address when reading.
But it doesn’t work in my case – when I add 0x80 – I am getting 0. But when I read without adding – I am getting correct results.
I am able to write to the registers of an rm3100 and read them. I tried to write to the register and then read its value - it works as expected.
But the measurement registers not changing and the senior bit of the status register (0x34) is always 0. DRDY line stays low.
I tried continuous mode (wrote 0x71 to the register 0x01) and single measurement (wrote 0x70 to the register 0x00).
Code: Select all
uint8_t data[1];
write_i2c_register(0x33, 0x8f); // wrote to the test register 0x33
usleep(1000000);
read_i2c_registers(0x33, data, 1);
printf("Test register is %02x\n", data[0]); // printing 0x8f in 0x33 register
write_i2c_register(0x00, 0x70); // initialize single measurement
usleep(1000000);
read_i2c_registers(0x34, data, 1);
printf("Status register is %02x\n", data[0]); // printing 0x00 in 0x34 register
write_i2c_register(0x01, 0x71); // initialize continuous measurement
usleep(1000000);
read_i2c_registers(0x34, data, 1);
printf("Status register is %02x\n", data[0]); // printing 0x00 in 0x34 register1) According to the datasheet https://www.pnicorp.com/wp-content/uplo ... -R09-1.pdf – I need to add 0x80 to the register address when reading.
But it doesn’t work in my case – when I add 0x80 – I am getting 0. But when I read without adding – I am getting correct results.
Code: Select all
std::vector<int> regs = {0, 1, 4, 5, 6, 7, 8, 9, 11, 36, 37, 38, 39, 40,
41, 42, 43, 44, 51, 52, 53, 54};
for (auto i: regs)
{
read_i2c_registers(i, data, 1); // when I read without adding 0x80
printf("%02x=%02x ", i, data[0]); // I am getting reasonable values
}
printf("\n");
for (auto i: regs)
{
read_i2c_registers(i + 0x80, data, 1); // when I add 0x80 to the reg address
printf("%02x=%02x ", i, data[0]); // I am getting zeros
}
printf("\n");But it doesn’t work in my case – when I add 0x80 – I am getting 0. But when I read without adding – I am getting correct results.
Code: Select all
void read_i2c_registers(uint8_t reg, uint8_t* data, const uint8_t bytes){
i2c_cmd_handle_t cmd = i2c_cmd_link_create();
ESP_ERROR_CHECK(i2c_master_start(cmd));
ESP_ERROR_CHECK(i2c_master_write_byte(cmd, (I2C_ADDRESS_GEO << 1) | I2C_MASTER_WRITE, 1));
ESP_ERROR_CHECK(i2c_master_write_byte(cmd, reg, 1));
// ESP_ERROR_CHECK(i2c_master_stop(cmd)); // <-- timeout when uncommented
ESP_ERROR_CHECK(i2c_master_start(cmd));
ESP_ERROR_CHECK(i2c_master_write_byte(cmd, (I2C_ADDRESS_GEO << 1) | I2C_MASTER_READ, 1));
if (bytes > 1)
ESP_ERROR_CHECK(i2c_master_read(cmd, data, bytes - 1, (i2c_ack_type_t) 0));
ESP_ERROR_CHECK(i2c_master_read_byte(cmd, data + bytes - 1, (i2c_ack_type_t) 1));
ESP_ERROR_CHECK(i2c_master_stop(cmd));
auto err = i2c_master_cmd_begin(I2C_NUM_0, cmd, 1000/portTICK_PERIOD_MS);
i2c_cmd_link_delete(cmd);
if (err != ESP_OK)
{
std::cout << "err=" << int(err) << "\n";
}
}
void write_i2c_register(const uint8_t reg, const uint8_t data){
i2c_cmd_handle_t cmd = i2c_cmd_link_create();
ESP_ERROR_CHECK(i2c_master_start(cmd));
ESP_ERROR_CHECK(i2c_master_write_byte(cmd, (I2C_ADDRESS_GEO << 1) | I2C_MASTER_WRITE, 1));
ESP_ERROR_CHECK(i2c_master_write_byte(cmd, reg, 1));
ESP_ERROR_CHECK(i2c_master_write_byte(cmd, data, 1));
ESP_ERROR_CHECK(i2c_master_stop(cmd));
esp_err_t err;
do err = i2c_master_cmd_begin(I2C_NUM_0, cmd, 1000/portTICK_PERIOD_MS);
while (err != ESP_OK);
i2c_cmd_link_delete(cmd);
}