SDIO & WIFI

[DiEitch]

Hi.
When I turn on WiFi

Code: [Select all] [Expand/Collapse]

1. esp_err_t wifi_setup() {
2.     esp_err_t ret;
3.  
4.     WiFi.mode(WIFI_STA);
5.     WiFi.disconnect(true);
6.     WiFi.onEvent(WiFiEvent); //not depend
7.     delay(100);
8.     return ESP_OK;
9. }

GeSHi © Codebox Plus Extension

sdio_slave is hangs.

I also try init with low level:

Code: [Select all] [Expand/Collapse]

1. esp_err_t wifi_setup(void)
2. {
3.     //s_wifi_event_group = xEventGroupCreate();
4.     esp_err_t ret;
5.     tcpip_adapter_init();
6.     ret = esp_event_loop_create_default();
7.     if (ret != ESP_OK) return ret;
8.     wifi_init_config_t cfg = WIFI_INIT_CONFIG_DEFAULT();
9.     //cfg.event_handler = NULL;
10.     ret = esp_wifi_init(&cfg); //OK BUT SDIO HALTED AFTER
11.     if (wf_debug)
12.     {
13.       if (ret==ESP_OK) Serial.println("WiFi= Init OK ");
14.       else Serial.println("WiFi= Init ERR ");
15.     }
16.     if (ret != ESP_OK) return ret;
17.     ret = esp_event_handler_register(WIFI_EVENT, ESP_EVENT_ANY_ID, &event_handler, NULL);
18.     if (ret != ESP_OK) return ret;
19.     ret = esp_event_handler_register(IP_EVENT, IP_EVENT_STA_GOT_IP, &event_handler, NULL);
20.  
21. //    wifi_config = {
22. //        .sta = {
23. //            .ssid = DEFAULT_SSID,
24. //            .password = DEFAULT_PWD,
25. ////            scan_method : DEFAULT_SCAN_METHOD,
26. ////            sort_method : DEFAULT_SORT_METHOD,
27. ////            .threshold.rssi = DEFAULT_RSSI,
28. ////            .threshold.authmode = DEFAULT_AUTHMODE,
29. //        }
30. //
31. //    };
32.     return ret;
33. }

GeSHi © Codebox Plus Extension

sdio hangs after esp_wifi_init()

Please help, what happened?

[felixcollins]

Try selecting the following option in "make menuconfig"

Component config / LWIP /USE_ONLY_LWIP_SELECT [=y].

[DiEitch]

Hi felixcollins.
Thank for reply.
I had no find this option in LWIP section.


With the best regards.

[DiEitch]

I check "Support LWIP socket select() only" because
https://github.com/espressif/esp-idf/bl ... ip/Kconfig.

[DiEitch]

Hi.
I tried to change, but nothing has changed. Can there be something else?
Also I tried to change directly in sdkconfig.

Who can tell, after changing sdkconfig, I need to do something else if I work in the Arduino IDE?

[felixcollins]

Sorry, I'm not sure what your problem is. You will need to debug deeper in the code and figure out where it is broken - you will probably need JTAG debugging for this.

I just had a problem similar to your one where httpd failed after mounting a file using fat https://www.esp32.com/viewtopic.php?f=13&t=10733

[DiEitch]

Hallo.

In any case, thanks for the reply!
I create issue: https://github.com/espressif/arduino-esp32/issues/2860
This problem be in arduino and in eclipse too.
But when I use eps32-at with SDIO mode - all works fine in 1 bit mode.

With the best regards.